Cabot® Solid Color Oil Stain

Cabot® Solid Color Oil Stain combines maximum color and UV protection with a tough alkyd resin. The results are a completely opaque finish that imparts lasting beauty and is formulated to withstand foot traffic and wear.

  • Water-repellent
  • Superior durability
  • Scuff resistant
  • Penetrating oil to withstand heavy foot traffic


Coverage
200 ft²/gal - 500 ft²/gal
For Use In Location
Exterior
Opacity
Solid
Dry Time
24 hour - 48 hour
Recommended Coats
2
Dry to Recoat
24 hour
Package Sizes
1-Gallon
Cleanup
Mineral Spirits

Reviews

Application Directions

  • Before You Begin instructions
    • Surface should be clean, porous and free of any previous finishes
    • For concrete: sprinkle a few drops of water on the surface; if they are quickly absorbed then the surface is ready to prep
    • Let wood dry in the open air for 3-5 days
    • Always apply to a small test area and allow to dry
    • Cover nearby bushes and flowers
    • Apply when air and surface temperatures are between 50 ˚F and 90 ˚F
  • Preparation Warning
    WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.
  • SURFACE PREPARATION
    • If needed, sand with 80-100-grit (120-180 grit for rougher surfaces) sandpaper to remove any loose wood fibers
    • Replace severely damaged or rotting boards
    • Clean with Cabot Wood Cleaner to remove dirt, grime, mildew and other contaminants
    • If needed, brighten with Cabot Wood Brightener to remove rust stains, tannin bleed or discoloration
    • If needed, remove old water- or oil-based coatings with Cabot Wood Stripper and neutralize with Cabot Wood Brightener
    • Check the label for additional and specialized directions
  • APPLICATION STEPS
    • Apply with a natural bristle brush or professional spray equipment. When spraying, always back brush immediately.
    • Do not overapply
    • Shake and stir thoroughly before and during use. If project requires more than one container, blend all containers together to ensure uniformity.
    • Apply to small sections at a time (1–3 boards); start at one edge of the board and work end-to-end, following through to the end of the boards to avoid lap marks
    • A one-coat application is recommended; two coats may result in a higher sheen
  • CAUTIONS
    CONTAINS ALIPHATIC HYDROCARBONS. Contents are COMBUSTIBLE. Keep away from heat and open flame. VAPOR HARMFUL. Use only with adequate ventilation. To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches, or dizziness, increase fresh air, or wear respiratory protection (NIOSH approved) or leave the area. Avoid contact with eyes and skin. Wash hands after using. Keep container closed when not in use. Do not transfer contents to other containers for storage. FIRST AID: In case of eye contact, flush thoroughly with large amounts of water for 15 minutes and get medical attention. For skin contact, wash thoroughly with soap and water. In case of respiratory difficulty, provide fresh air and call physician. If swallowed, call Poison Control Center, hospital emergency room, or physician immediately. DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Contains solvents which can cause permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents can be harmful or fatal. WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. DO NOT TAKE INTERNALLY. KEEP OUT OF THE REACH OF CHILDREN. DANGER: Rags, steel wool, other waste soaked with this product, and sanding residue may spontaneously catch fire if improperly discarded. Immediately place rags, steel wool, other waste soaked with this product, and sanding residue in a sealed, water-filled, metal container. Dispose of in accordance with local fire regulations.

Cabot® Solid Color Oil Stain

Product Number Base/Color Container Size SDS PDS
080351116018 White 1 Gallon SDS PDS
080351116063 Neutral Base 1 Gallon SDS PDS
080351116087 Medium Base 1 Gallon SDS PDS