Cabot® Australian Timber Oil® Low VOC

Cabot® Australian Timber Oil® penetrates even dense exotic hardwoods in just one coat. With superfine pigments that never peel and resist brush marks, you’ll be able to enjoy a choice of 5 rich colors that won’t fade or scuff for years to come.

  • Superior 3-oil formula
  • Lasting protection from UV damage
  • Creates mold- & mildew-resistant finish
  • Rich color & grain definition
  • Ideal for decks and outdoor furniture

250 ft²/gal - 350 ft²/gal
For Use In Location
Dry Time
24 hour - 48 hour
Recommended Coats
Dry to Recoat
Package Sizes
1-Quart, 1-Gallon, 5-Gallon
Water Cleanup
Cleanup Details
Clean up with warm, soapy water


Application Directions

  • Before You Begin instructions
    • Surface should be clean, porous and free of any previous finishes
    • For concrete: sprinkle a few drops of water on the surface; if they are quickly absorbed then the surface is ready to prep
    • Let wood dry in the open air for 3-5 days
    • Always apply to a small test area and allow to dry
    • Cover nearby bushes and flowers
    • Apply when air and surface temperatures are between 50 ˚F and 90 ˚F
  • Preparation Warning
    WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.
    • If needed, sand with 80-100-grit (120-180 grit for rougher surfaces) sandpaper to remove any loose wood fibers
    • Replace severely damaged or rotting boards
    • Clean with Cabot Wood Cleaner to remove dirt, grime, mildew and other contaminants
    • If needed, brighten with Cabot Wood Brightener to remove rust stains, tannin bleed or discoloration
    • If needed, remove old water- or oil-based coatings with Cabot Wood Stripper and neutralize with Cabot Wood Brightener
    • Check the label for additional and specialized directions
    • Apply with good-quality, natural-bristle brush, stain pads or professional spray equipment.
    • When spraying, always back brush immediately. To ensure desired appearance and proper drying time, always finish a small test area before proceeding. Do not overapply.
    • Shake and stir thoroughly before and during use. If project requires more than one container, blend all containers together to ensure uniformity.
    • Apply to small sections at a time (1-3 boards); start at one edge and follow through to the end of the boards to avoid lap marks.
    • Apply one coat only. For wood substrates only.
    Use only with adequate ventilation. To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches, or dizziness, increase fresh air, or wear respiratory protection (NIOSH approved) or leave the area. Avoid contact with eyes and skin. Wash hands after using. Keep container closed when not in use. Do not transfer contents to other containers for storage. FIRST AID: In case of eye contact, flush thoroughly with large amounts of water. Get medical attention if irritation persists. If swallowed, call Poison Control Center, hospital emergency room, or physician immediately. WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. DO NOT TAKE INTERNALLY. KEEP OUT OF THE REACH OF CHILDREN. DANGER: Rags, steel wool, other waste soaked with this product, and sanding residue may spontaneously catch fire if improperly discarded. Immediately place rags, steel wool, other waste soaked with this product, and sanding residue in a sealed, water-filled, metal container. Dispose of in accordance with local fire regulations.

Cabot® Australian Timber Oil® Low VOC

Product Number Base/Color Container Size SDS PDS
080351810015 Natural 1 Quart SDS PDS
080351810008 Natural 1 Gallon SDS PDS
080351810022 Natural 5 Gallon SDS PDS
080351812125 Tint Base 1 Gallon SDS PDS
080351810046 Amber Wood 1 Quart SDS PDS
080351810039 Amber Wood 1 Gallon SDS PDS
080351810060 Honey Teak 1 Quart SDS PDS
080351810053 Honey Teak 1 Gallon SDS PDS
080351812644 Honey Teak 5 Gallon SDS PDS
080351810084 Mahogany Flame 1 Quart SDS PDS
080351810077 Mahogany Flame 1 Gallon SDS PDS
080351810091 Mahogany Flame 5 Gallon SDS PDS
080351810114 Jarrah Brown 1 Quart SDS PDS
080351810107 Jarrah Brown 1 Gallon SDS PDS
080351812200 Jarrah Brown 5 Gallon SDS PDS